Channging the Control Station IP address on NS-120...

I'll give you the quick way to do this, because emc has tons of info on their powerlink site and most of it is outdated. By outdated I mean it doesn't really need to be done that way with newer version of DART. So as of code 5.6.4x-x the following should work. I was on version 5.6.41-2.
Change the IP address on the Control Station 1st, then change the SPA and SPB.

1. Use your favorite web browser to login to the Control Station (current ip address)
   Login as root.
   
2. Look under the tab for Control Station Properties, and change the IP Address information, Gateway, subnet, DNS, NTP, etc. click apply.
3. Reboot the control station. This can be done from the same Control Station Properties Tab. at the bottom there is a reboot button.

Now what about SPA and SPB?? If you need to change them as well this needs to be done through the command line. Use your favorite SSH application to login to the new ip you setup for the control station.

1. Login as nasadmin.
2. su root
3. run the following command:
4. /nasmcd/sbin/clariion_mgmt -modify -spa_ip xxx.xxx.xxx.xxx -spb_ip xxx.xxx.xxx.xxx
5. The results should look something like this:
   

Checking if running as root...yes
Checking if model is supported...yes
Checking for integrated system...yes
Checking if interface eth3 is configured...yes
Checking if interface eth3:1 is configured...no
Checking if interface eth3:2 is configured...no
Checking if SP (10.64.247.141) is up...yes
Checking if SP (10.64.247.142) is up...yes
Checking if a gateway is setup for eth3...yes
Step 1/7: Setting up Proxy ARP for SPA on Control Station
Adding host specific route for SPA
Adding rules to allow outbound traffic from SPA
Adding ARP entry for SPA
Updating /etc/hosts entry for SPA
Step 2/7: Changing SPA IP address.
Changing SPA IP from 10.64.247.141 to 10.64.247.147 (subnetmask 255.255.255.0, gateway 10.64.247.1)
Step 3/7: Waiting for SPA to reboot.
Waiting for SPA to go down...done
Step 4/7: Waiting for SPA to boot up.
Waiting for SPA to come back up...done
Step 5/7: Waiting for CLARiiON software to start on SPA.
Waiting for CLARiiON software to start on SPA..................done
Step 6/7: Removing old Proxy ARP setup for SPA on Control Station
Removing host specific route for SPA
Removing rules that allow outbound traffic from SPA
Removing ARP entry for SPA
Step 7/7: Updating NAS database with SPA IP address
Updating SYMAPI database with new CLARiiON IP addresses...done

VMDK Recovery Tool with 3.5 update 3

I was taking a look at some of the release notes for esx 3.5 update 3 and noticed a VMDK recovery tool. This is experimental and has tons of warnings, but in some cases it may work for rudimentary backup, and looks to foreshadow some possible backup features to come. There is a script intended to help customers to recover VMFS and VMDK data stores from accidental deletion of a data store or physical disk corruption. Basically looks to be a very basic backup and recovery functionality. Check out this KB link it goes through an example:
http://kb.vmware.com/selfservice/microsites/search.do?language=en_US&cmd=displayKC&externalId=1007243

NDMP Shortcut for Celerra

Here's a quick primer for setting up NDMP on the Celerra. This post is assuming that you are working with FC tape device and you have it connected to the aux port for the datamover on server_2. Note that configuring the NDMP option on the celerra has you shutting down the data movers, and that means no access to CIFS or iSCSI Luns that are published through the Data Movers, so plan accordingly!

From the Control Station, halt each Data Mover to be connected to the TLU and confirm it has halted by using this command syntax:

• $ server_cpu -halt -monitor now

server_cpu server_2 -halt -monitor now

• Type /nas/sbin/getreason and ensure that the status is powered off.

Cable each Data Mover to the Tape Library.
Turn on the Tape Library and verify that it is online. Restart each Data Mover connected to the Tape Library and confirm it has restarted by using this command syntax:

• $ server_cpu -reboot -monitor now

server_cpu server_2 -reboot -monitor now

• This could take 5 minutes or so…

After the Data Mover restarts, verify that the Data Mover can recognize its Tape Library device by using this command syntax:

• $ server_devconfig -probe -scsi –nondisks

server_devconfig server_2 -probe -scsi –nondisks

Save the Data Mover’s TLU devices to the Celerra Network Server database by using this command syntax:

• $ server_devconfig -create -scsi –nondisks

CAUTION: In a CLARiiON environment, before you run the server_devconfig -create command, verify that all paths to the Data Mover are active and no LUNs are trespassed. Running this command while paths are inactive causes errors in the Data Mover configuration file.

server_devconfig server_2 -create -scsi –nondisks

List the device addresses by using this command syntax:

• $ server_devconfig -list -scsi –nondisks

server_devconfig server_2 -list -scsi –nondisks

• The output will look similar to:
  Server_2 :
  Scsi device table
  name addr type info
  jbox1 c1t0l0 jbox ATL P1000 62200501.21
  tape2 c1t4l0 tape QUANTUM DLT7000 245Fq_
  tape3 c1t5l0 tape QUANTUM DLT7000 245Fq_

To assign a user account name and password to one or more Data Movers, log in to the
Control Station as nasadmin and switch user to root by typing:

• $ su
• Type the root password when prompted.
• To create an account, use the appropriate command syntax, as follows:
  Text method:
• # /nas/sbin/server_user -add -password
  MD5 password encryption method:
• # /nas/sbin/server_user -add -md5 -password

/nas/sbin/server_user server_2 -add -md5 -password NDMPuser

• The output will look similar to:
  Creating new user NDMPuser
  User ID: 1000
  Group ID: 1000
  Home directory:
  Changing password for user NDMPuser
  New passwd:
  Retype new passwd:
  server_2 : done

Now you are ready to configure the backup solution to the celerra. This process will vary depending on the backup software. Basically, the next step is to add the NDMP server to the backup server using the ip address or hostname of the data movers and use the credentials you setup above. This will allow you to see the CIFS shares on the backup server, and will allow you to create a media set for the tape device and create backup jobs for the CIFS data.

More Avamar Basics

My last blog went through a basic intro to Avamar. I'll pick up where I left off and go through some of the basic configurations that are supported, and when to use them.

Avamar Server Node Types:

• The Utility Node is the brains of the avamar server. It is dedicated to providing the internal server processes including the administrator server, cron jobs, scheduling, DNS, authentication, NTP, and web access.
• The Data Storage Node is where all the data resides. Once the data is backed up and deduped from the client, it is stored on the Data Storage Node.
• The NDMP Accelerator Node is an option node for providing backup and recovery solutions to NAS devices like the Celerra.
  

Standard configurations for Avamar:

• Single Node. Also known as the Non-RAIN (Redundant Array of Independent Nodes) configuration. This is the entry level configuration in which the single node acts as the utility node and the data storage node. When using this configuration 2 single nodes are needed. 1 is the main backup node, and the 2nd is used for replication purposes for fault tolerance. Used in small to medium sized environments for a max of 2 Tb of storage.
  
• Muti-Node Non RAIN. This is basically is a 3 node setup consisting of 1 Utility Node and 2 Data Storage Nodes. It allows for double the storage capacity of a Single Node device.
  This configuration also needs a duplicate setup for replication, so a total of 6 Nodes would be needed for fault tolerance. Used in medium sized environments with a max of 4Tb of storage.
  
• Multi-Node RAIN. The Standard RAIN configuration has 1 Utility Node, 4 Data Storage Nodes and 1 Spare Node. This configuration can be expanded for a total of 16 Data Storage Nodes max. All of the nodes work together to balance the storage equally across all of the other Data Storage Nodes. This architecture is easily scaled from 6Tb to 32 Tb by adding as many Storage nodes as necessary. Typically used in large environments, this configuration can be initially setup with 3 Storage nodes instead of the standard 4 Storage nodes. It is recommended to setup a duplicate Multi-Node RAIN for replication, typically at a DR site. Although it is recommended, it is not a necessity like the Non-RAIN configurations, because there is a spare node that can be configured at any point for fault tolerance.
  
• Virtual Appliance. The Virtual Appliance is a software-only solution that comes in either .5 Tb or 1Tb editions. The appliance is essentially a vm of the Single Node version with the same characteristics. It is installed in ESX environments and is ideal for small environments or remote facilities.
  

What exactly is Avamar?

Avamar from EMC has a refreshing new twist on the backup world. This solution utilizes backup to disk hardware and client software installs to create a client-server network backup/restore solution while using a unique de-dupe technology.

Traditional Backup solutions have some significantly inherent problems. A high-percentage of data that is retained on backup solutions is redundant data. Typical strategies consist of daily incremental backups and weekly full backups. These backups can be very time consuming, especially when getting the full backups, and yield multiple copies of identical or slowly changing data on backup media. This media then has to be organized and kept off-site for disaster recovery purposes, which often leads to high protection service costs, and high recovery time objectives. In addition, the data itself that is often duplicated across several servers in the case of system files, and many users keep identical or slightly different versions of the same documents. Traditional backups will backup all copies and variations as if they were brand new documents. Backing up redundant data increases the amount of backup storage needed and can negatively impact network bandwidth. The backup window for most organizations gets smaller and smaller the more they grow.

Avamar differs from traditional backup and restore solutions by identifying and storing only unique data objects. Redundant data is identified at the source, which reduces the amount of data that actually needs to travel to the backup server node. Avamar utilizes a chunk and hash methodology to break down all files into smaller chunks of data to send to the backup node. Unique hashes are generated from this data that gets stored on the backup node. If a client tries to send the same data, the backup node will respond that it already has that data and does not need another copy. Only new, modified, or changed chunks from the original files will be sent to the backup node.

Some of the key features:

• Global data de-duplication ensures that data objects are only backed up once across the backup environment.
• Systematic fault tolerance, using RAID, RAIN, checkpoints, and replication provides data integrity and disaster recovery protection.
• Highly reliable inexpensive disk storage for primary backup storage.
• Standard IP network technologies. Optimizes use of network for backup, does not require a separate backup network.
• Centralized management. The Avamar Administrator and Enterprise consoles give users full-featured remote management of Avamar servers with robust reporting capabilities.
• Support for Windows, Unix, Linux, NDMP, SQL, Exchange, DB2, and Oracle.

So now that you have some of the basics, check back soon to get a more in depth look to how the different solutions are deployed. There are 3 basic versions:

• Avamar Data Store Non-RAIN (single or multiple nodes with replication)
• Avamar Data Store RAIN (multiple data nodes for fault tolerance)
• Avamar Virtual Edition (virtual appliances versions in .5 and 1 TB)

EMC's new CX4

I have recently been some reading on EMC's new CX4 line and thought I should share a little background information. So what all is new???
Bigger, Faster, Better...
Here is a basic breakdown of the models.
Click on the image for a clearer picture.



The CX4 line introduces a new naming convention, that coincides with the number of drives that are supported. Finally, a simple approach to the most popular question regarding the different Clariion models. The only exception is the AX4, which probably should have been named the Ax4-60

There are now modular ports for customizable connectivity.

• Number of front-end FC ports and front-end iSCSI ports are configurable for each model
• Number of back-end FC ports is fixed for CX4-120,CX4-240,CX4-480
• Number of back-end FC ports is configurable for CX4-960
  (choose between 8 or 4 back-end ports per SP)
• Front-end connectivity options: FC (4Gbps), iSCSI (1GbE)

There is much more memory for better cache performance.

• CX4-120 has 6Gb
• CX4-240 has 8Gb
• CX4-480 has 16Gb
• CX4-960 has 32Gb

The CX4-120 is rated as the entry level device, but when compared to its little brother, the CX3-10, it is quite the upgrade. Take a look at the basic break down for a better comparison. Click on the image for a clearer picture.



CX4 & CX3 DAE and Disk Considerations:

• DAE's are the same for the CX3 & CX4 arrays

CX4 disk drives qualified

• 400GB 10k rpm disk with 4Gbps Fibre Channel interface
• 146GB 15k rpm disk with 4Gbps Fibre Channel interface
• 300GB 15k rpm disk with 4Gbps Fibre Channel interface
• 1TB 5400 rpm SATA drive with 3Gbps SATA II interface
  (low power)- New Tier 3 storage
• 1TB 7200 rpm SATA drive with 3Gbps SATA II interface
• Disk qualifications carry over from CX3
• SATA-II drives can act as Vault drives on the CX4-120 model only

CX4-960 offers flash drives !!!
NOTE: currently they are only offerred for the CX4-960

• Support for customized Flash SSD (Solid State Drive)
  for high-performance Tier 0 applications
• EMC optimized Solid State Drive technology
• Internal SDRAM buffers and pipelining provide maximum performance
• No rotational latency or seek overheads provides incredible response time
• Ideal for low-latency, high-transaction workloads
• Native Fibre Channel interface
• 3.5” form factor for use with existing DAEs
• Flash drives need a separate DAE from traditional disks.
  

CX4 Disk Placement Best Practices

• Configure SATA and FC drives in separate DAEs
• 1TB 5400 rpm low power SATA drive will only be sold as a “15 drives per tray” package (fully populated DAE)
• This prevents mixing with 7200 rpm SATA drives within one DAE

Only the CX4-120 model supports:

• 1TB 7200 rpm SATA drive as Vault drives
• 1TB 5400 rpm low power SATA drive cannot be used as a Vault drives
  

XenApp 5

I have been in training this week for Citrix, so I figured I should spread the word on some of the things I've learned. The training is all on Presentation Server 4.5, but there was some good info on the new release which is called XenApp 5... But you already knew that. I'll summarize some of the highlights.

Web Interface 5.0 for Windows.
The old web interface was how can I say this politely, less than impressive. There is a very nice face lift for the 5.0 version. Let's face it with all the eye candy out there now a nice user interface is not only the norm, but becomes part of function.

• Breadcrumb navigation bar which replaces the old Home, Top, and Up links.
  
• User-selectable views to allow preferred display of published resources, with new features like tree views and group views.
• User-assistance to give helpful hints and help for the end users.
• Simple and Advanced modes for a more customizable look and feel.
• Mobile experience enhancements for the users with hand-held devices and integration with the Access Gateway.
• XenDesktop Support which allows users to access virtual desktops through the web interface.
• Web Interface for Sharepoint which makes it possible to deliver XenApp published apps and resources on to Sharepoint 2007. (Separate install)

XenApp Plugin for Hosted Apps. This plugin is basically new name for the Presentation Client Agent. It's functionality remains very similar, but the look and feel have changed.

• Improved support for Vista and Office 2007.
• Updated menu structure.
• little or no user configuration required.
• Web Interface integration and streamed app integration.
• Password change capability.

XenApp Plugin for Streamed Apps. This plugin provides streamed applications from the target, file, or web server to XenApp servers and client desktops. Some of the new features include:

• Integration with XenApp Web Plugin and XenApp Plugin to stream apps to the desktop.
• No user configuration required, and seamless integration to the end users.
  
• Improved inter-isolation communication between multiple applications that are running in isolated profile environments.
• Differential synchronization to reduce latency and improve performance.

Resource Manager for XenApp. This module received a face lift powered by Citrix EdgeSight technology, which was previously a platinum level feature. It still supports the original reporting as the previous version of Resource Manager with some new features:

• Session-level performance counters.
• Real-time alerting.
• More pre-configurable and customizable and reporting.
• Integration with Health Check Agent.
• Active application monitoring.

Citrix License Server 11.5. This new updated license service is backward compatible, but is now flexlm based. Basic requirements for a license server:

• Internet Explorer 5.0 or higher.
• Tomcat 4.1.24.
• JRE 1.6.0_5 or later.
• Apache HTTP Server 2.0.49.
• IIS must be installed prior to install.
• ASP.Net, Windows Authentication Security, and IIS Mangement 6.
• supported on Windows 2000, 2003, and 2008

XenApp 5.0 Platinum Edition components. Here is the overview.

• Application Performance Monitor powered by Citrix Edgesight. This component adds ICA monitoring, service-level management and more to the Resource Manager feature included in the Enterprise Edition.
• Single Sign-on powered by Citrix Password Manager 4.6 SP1. Password Manager provides secure and managed access to applications running in the Citrix environment as well as the local apps on the desktop.
• Citrix Accelerator Plugin formerly WANScaler Client License. Provides WAN optimization and applicaiton accceleration for home-based, mobile or small office users.
• Citrix SmartAuditor. Records and plays user sessions using policies to automatically trigger the recordings.
  
• EasyCall. Embeds VOIP like triggers allowing users to click any telephone number in any app to make a call.